#Bible analyzer for ipad full
#Bible analyzer for ipad software
#Bible analyzer for ipad plus
#Bible analyzer for ipad free

#Bible analyzer for ipad free

OneTouch Light OneTouch Light is a free version of Biblesoft’s award-winning Bible study program intended for new users – those who have not yet tried using our study software. getting more ‘thunder’ out of the floor tom), but make this should be the exception rather than the rule.OneTouch Light is a free version of Biblesoft’s award-winning Bible study program intended for new users – those who have not yet tried using our study software. There are cases where you will boost frequencies (i.e. When you cut out frequencies you don’t want, it allows the right frequencies to shine. The biggest tip I can give you when it comes to EQ is to cut frequencies, not boost them.

#Bible analyzer for ipad full

And, our sound is full of energy, fills the room, but no longer hurts your ears. Now, we can run the vocals where they need to be without fear of feedback. It took me about 3 weeks to get the sound I wanted, but it was well worth the effort. So, pull out your iPhone and analyze the sound as the band plays and fine tune as necessary. But, once you bring in the band, you may find that you have cut too much somewhere, leaving a hole in the sound. Step 5: Bring in the band and make necessary adjustments.Īfter EQing with pink noise, you will have a great starting point. Refer back to step 3 for a reference on what you are trying to achieve. You are only looking for those that stick way out from those around it.Īlso, there should be a gradual drop off after about 800Hz. Keep in mind, the goal is not to get every frequency the same level. Continue adjusting EQ until you have successfully cut all those that are sticking out. Tip: you can hold your thumb down to highlight specific frequencies. The peaks show you what frequencies are sticking out above the rest.Open the Octave iPhone app and analyze the sound from the middle of the room while pink noise is playing.Play it loud enough to fill the room with sound. Use something other than your iPhone to play pink noise through your sound system.So you will need to run a test for your room using the following steps. I could tell you the frequencies we have to cut in our room, but it wouldn’t help you as every room is different. We have since installed a significant amount of sound absorbing panels, which helped tremendously, but a good amount of EQ is still necessary to achieve a good sound. The room is long and narrow, we have concrete floors, plastic chairs and hardly any sound absorbing surfaces. In our current venue, there are lots of problems. Step 4: Using pink noise, find the room’s troublesome frequencies.Įvery room has its problems, some more than others. The main thing to notice is where the higher frequencies begin to fall of, which would explain why their sound is so warm and powerful, but still plenty of clarity. The two screen shots were taken during two different songs. I also took a few screen shots to help me remember (see below). So, I went to one of their events, pulled out my iPhone during worship and examined what was going on. In my opinion, Church on the Move in Tulsa has the best sound of any venue I have ever been in. This will give you an idea of what you need work towards. Then, pull out your iPhone and analyze the sound. Step 3: Determine your baseline measurement.īefore you start analyzing the sound at your church, I recommend going to another church or venue where you like the overall sound. On the bottom of the screen, use the following settings:

#Bible analyzer for ipad plus

On the plus side, they are more accurate than the iPhone app, but with a little tweaking, the iPhone app will work just fine.

#Bible analyzer for ipad software

Keep in mind, there are other software and hardware solutions for RTA sound frequency analyzers, but at $300+ the cost is significantly more. It will save you hours of headache and help you reach your goal of the best sound possible. You will be so glad that you spent $5 on this app. Note: If you are using the X32, follow this post instead. You no longer have problems with feedback and you can run your sound at a higher volume without irritating people’s ears.Īctually, when someone says that the sound is too loud, it is generally just one part of the frequency spectrum that is too loud, not the overall sound.īy using the following tools, you will be able to analyze sound, find bothersome frequencies, and cut them so they fit with the rest of the sound spectrum. When you get EQ right, the end result is amazing.